Professional turnkey installation of heating systems
We design, select equipment, install and service heating systems all over Ukraine
Free visit to the facility and engineer consultation
We know the value of your time, so we make a commercial offer as soon as possible.
The importance of a well-designed heating system
When designing a heating system, it is important to answer many technical questions about the parameters for a particular room. They include boiler capacity, fluid velocity, location of radiators, capacity of each radiator, pipe material, their arrangement, pipe section diameter, and type of shut-off valves.
Thermal and hydraulic calculations can help to answer these and other similar questions. If this important issue is omitted, it can lead to overspending or an imbalanced system.
Compensation of heat losses and maintaining the temperature at a predetermined level
normalization of a thermal comfort and/or technological process requirements
normalizes humidity in the room
What risks does the client bear in case of incorrect installation of the heating system?
Losses due to poor-quality materials, which can lead to system failure.
Incorrect hydraulic calculations. If the pipe diameter is incorrectly selected, then the system does not cope well and often fails.
Improper use of pipes. Improper use of pipes causes water in water supply systems to be of inadequate quality.
Incorrect installation. There are many nuances in the installation of heating systems. If material compatibility and the use of the right fittings are not considered, the system will break down and fail quickly.
Choosing a professional contractor is task number 1 when ordering heating installation
It depends on the knowledge and experience of the contractor whether all stages of work will be successful and on time. The skills of designers and specialists directly affect the quality and service life of the heating system.
What problems do clients face when choosing a company for the installation of heating system?
For the full cycle of work, it is necessary to look for several contractors. You have to coordinate their actions by yourself. This is the cost and duration of work.
Installers do not seem trustworthy; their approach to work gives the impression that they are installing heating for the first time.
Unreasonably expensive solutions are offered. Specialists do not take into account the energy consumption of the system when designing and choosing equipment.
In fact, maintenance of the heating system is difficult. Due to the lack of automation, you have to turn to third-party companies.
Not all contractors undertake non-standard tasks.
To avoid having to deal with these problems in person and wasting resources in correcting mistakes, choose a professional contractor from the first steps.
Why do clients contact us for heating system installation
SMARTKOMPLEKT is a professional engineering company that has been engaged in the design, installation and maintenance of ventilation, air conditioning and heating systems for 13 years. The qualities that our clients appreciate in working with us:
When creating a design, we take into account all the features of the facility, i.e. area, location and climatic conditions. The choice of heating type is determined by the availability of service lines such as gas, water, electricity or fuel for solid fuel boilers.
Solving non-standard tasks
Our extensive experience and our specialist’s in-depth knowledge allow us to take on non-standard facilities and offer solutions to even the most challenging tasks.
Flexible payment system
We optimize the client’s costs for the purchase, installation and maintenance of heating systems. We choose the optimal package of services and equipment so that even with a limited budget you can get a high-quality and functional solution.
Functional equipment configuration
We directly cooperate with well-known manufacturers of heating equipment. At the design stage, we select the most functional and reliable system equipment depending on the tasks and budget. We do not promote individual brands, but choose equipment whose quality has been tested in practice.
Responsible turnkey work
Clients trust us in the whole process: from documentation to the launch of the system and get heating at their facility. They do not have to worry about the progress of work, remind about deadlines and solve force majeure situations. The company’s managers are in touch 24/7 to promptly resolve any issues that may arise with the client.
Transparency of all solutions
We do not offer solutions that cannot be explained by functional purpose. If you have any questions, our engineers will tell you in detail why such a solution is needed at your facility.
Our company has license No. 2013047684, which confirms high qualification in the installation of engineering ventilation networks. All elements of the system and equipment are installed in accordance with the instructions and safety regulations. Installers take into account the special conditions at the facility, they are ready to adapt their methods under the circumstances and promptly resolve any problems.
Warranty and post-warranty service
We provide constant support in heating system maintenance. A client does not have to look for new contractors to clean or adjust the system. Our specialists perform maintenance quickly, as they are well aware of the device and features of the ventilation that they installed.
Our professionalism is confirmed
To put the facility into operation, it is necessary to have all the necessary documents and permits, be sure of the safety of the structure and the quality of work. A construction license is required for facilities of IV and V categories of complexity. These are buildings that are designed to accommodate more than 300 people. This category includes educational institutions, shopping centers, railway stations, government agencies, hotels, etc.
Provides permission to carry out activities for installation, maintenance and repair of fire safety equipment of buildings and structures.
This type of work is performed by professionals using special equipment. The mobility and reliability of such equipment allow for performing all types of construction or repair services, as well as installation and dismantling.
Works performed in areas of permanent or possible exposure to hazardous production factors, the occurrence of which is not related to the nature of the work performed, which require the development and implementation of additional safety measures for each specific production operation before the start of these works.
High-risk works are performed with a work permit.
Employees belonging to electrical and electro technical personnel must pass a test of knowledge of requirements. Rules and other safety requirements for the organization and performance of work in electrical installations within the requirements for the relevant position or profession.
warranty for work
2 to 5 years
Services we provide
Examination and diagnostics
SMARTKOMPLEKT specialists can conduct a comprehensive check of the installed heating system, i.e. detect malfunctions, measure pressure, and inspect the system for contaminations and leaks.
If a heating system has not yet been installed, the engineer visits the client's facility, inspects the premises and determines the current climatic conditions and tasks. A specialist checks whether access is open to the places where equipment is installed, water supply and uninterrupted power supply pipes are laid, or whether preparatory work is needed.
Design and documentation
Based on the client's tasks, the company's specialists draw up detailed technical documentation of the facility. The design department develops draft and detailed designs and prepares technical and legal documents necessary for system installation and commissioning.
Selection and delivery of equipment
Our company has been cooperating with manufacturers of equipment and consumables for 13 years. We do not promote individual brands, but cooperate with a whole list of well-known companies and choose the products that are ideally suited to the client's facility. We also undertake the delivery of all materials to the facility. When choosing equipment, we take into account
Installation and commissioning works
Installation of heating systems in accordance with the norms and requirements of the project documentation. Our specialists take into account the features of the purpose of the room, structures inside the room. Both the technical aspect of the issue is fully maintained, but also the aesthetic issue, which also matters.
Technical and post-warranty service
At the request of the client or in accordance with the terms of the contract, we check the operation of the existing heating system. In case of failures in the system, we promptly eliminate them.
Cleaning and disinfection
We carry out maintenance of the heating system within the time frame, taking into account the type of system and the need for frequency specified in the contract.
Automation and dispatching
Our electronics specialists equip the heating system with automatic control. Sensors monitor the heat carrier temperature, system pressure, room temperature, etc. If necessary, they activate the corresponding system or improve the operation of mechanisms. Automation allows adjusting the heating system operation according to the required climatic parameters on site or remotely, protecting against overloads and preventing emergencies.
Types of heating systems that we install
Depending on the conditions in the room and the tasks, we select the appropriate type of heating.
A heating system where the heat transfer inside is carried out by a liquid (water or antifreeze) is called a water heating system. The available liquid is heated from a heat source and transported through pipes to radiators located in the rooms, which serve as the main heating equipment. The temperature in such a system is adjusted either manually, by means of a thermostatic head mounted on the radiator, or automatically by heat regulators. Depending on the connection and method of pipe routing, a distinction is made between one-pipe, two-pipe or two-flow systems with top, bottom, vertical or horizontal distribution.
It is less common due to the high cost of electricity, despite the main advantage of such networks, i.e. the convenience of their use. The heating devices used in this type of heating system are
- Electric convection heaters are a more convenient alternative to radiators, but they often warm up the room unevenly;
- Electric boilers are often used in premises where it is problematic to install gas or solid fuel boilers;
- Electric underfloor heating is usually used as an additional source of heating.
Air heating is a method of heating by blowing hot air into the rooms. This type of heating system does not require:
- boiler room;
- pipelines that may freeze and become unusable;
- radiators that heat the walls more than the room itself.
In steam heating, water steam moves through pipelines. Its temperature ranges between 130°C and 200°C. This heating system is therefore often used in industrial companies which use steam as a by-product of their production processes.
Alternative sources of heating are systems that work with heat generators based on renewable energy sources. These are solar, geothermal and biological energy. Boilers, heat pumps and solar panels are used, which accumulate heat and produce electricity. This type of system is more expensive at the installation stage than our usual heating systems, but in operation, the costs are recouped in a few years and further save the consumer money.
Types of objects we work with
Shopping and entertainment centers
Office and administrative premises
Warehouse and production facilities
Cafés, restaurants, hookah bars
Hotels & casinos
Cottages and houses with an area from
Stages of work
1. Engineer's visit to the facility
An engineer visits the facility and inspects the premises or building. A specialist determines the type of heating that will provide the client with the necessary climatic conditions.
2. Calculation of the project and cost estimate
The design department prepares the terms of reference and cost estimate. Work structure and plan are formed in such a way that the costs are minimal, and the execution period is the shortest.
3. Project documentation
We undertake the preparation of project documents. We agree their content with the client beforehand.
4. Contract signing
This document shows the client what types of work and in what terms the contractor undertakes to perform. From the moment of signing the contract, our team begins the implementation of the project.
5. Purchase and supply of equipment
Thanks to many years of cooperation with manufacturers, we purchase devices and consumables according to a cost estimate at competitive prices. Well-established logistics allow us to ensure the integrity of the equipment during transportation.
We equip installers with all the necessary tools and create conditions for them to work safely.
Specialists equip heating with a system that automates its operation. They install and activate sensors, and integrate them with the control unit. Specialists instruct the client’s employees on how to configure and monitor the main indicators.
8. Testing and start-up
Specialists check the operation of all elements of the heating system: from the tightness of pipes and fittings to the reactions of the automated control unit. After testing, the system is put into operation.
A working heating system, depending on its type, needs regular technical inspection. Our specialists carry out routine diagnostics and maintenance of a heating system. In case of malfunctions, they promptly eliminate them.